What Is a GO/NOGO Gauge? How It Works, Types and Calibration
What a GO/NOGO gauge is, how it works, the main types, GO vs NOGO, materials, correct use and how often to calibrate. A practical guide from a gauge manufacturer and NABL lab.
Not every inspection needs a number. Very often, all you need to know is whether a feature is within tolerance or not. A GO/NOGO gauge answers exactly that, in about a second, with no reading, no calculation and no special skill. This guide explains what a GO/NOGO gauge is, how it works, the main types, and how to choose, use and calibrate one.
What is a GO/NOGO gauge?
A GO/NOGO gauge (also written go no go gauge, go/no-go gauge or limit gauge) is a fixed inspection tool made to the two limits of a toleranced dimension. It has two members, or two ends:
- The GO member is made to the maximum material limit. It must enter the hole, or pass over the shaft.
- The NOGO member is made to the least material limit. It must not enter the hole, or must not pass over the shaft.
If GO goes and NOGO does not, the part is within tolerance. If GO does not go, the feature has too much material and may be reworkable. If NOGO goes, the feature has too little material and is rejected.
Because a GO/NOGO gauge is a physical copy of your drawing limits, every operator gets the same answer. That is why limit gauges are still the standard method for high-volume inspection in automotive, fastener, hydraulic, aerospace and general engineering shops.
How does a GO/NOGO gauge work?
The working principle is simple:
| Feature | GO member size | NOGO member size | Accept when |
|---|---|---|---|
| Hole (bore) | Lower limit of the hole | Upper limit of the hole | GO enters, NOGO does not |
| Shaft (outside diameter) | Upper limit of the shaft | Lower limit of the shaft | GO passes over, NOGO does not |
For example, a bore of Ø20 H7 has limits of 20.000 mm to 20.021 mm. The GO plug is made at 20.000 mm and the NOGO plug at 20.021 mm, each with a small gauge-maker's tolerance and, on the GO side, a wear allowance.
Taylor's principle
Good GO/NOGO gauges follow Taylor's principle of gauging:
- The GO gauge checks the whole feature at once, at maximum material. It should be full-form and, ideally, as long as the feature, so it also catches form errors such as bending, ovality or taper that would stop a mating part from assembling.
- The NOGO gauge checks one dimension at a time, at least material. It is usually shorter, so that a local oversize is detected.
This is also why the NOGO end of a plain plug gauge is shorter than the GO end, and why a NOGO thread gauge has a truncated profile and fewer threads.
Types of GO/NOGO gauges
GO/NOGO gauges exist for almost every feature on a drawing:
- Plain plug gauges for checking bores and holes.
- Plain ring gauges for checking shafts and outside diameters.
- Snap (gap) gauges for fast checking of outside diameters and thicknesses without removing the part from the machine. Double-ended (D/E) snap gauges carry the GO and NOGO gaps on opposite ends.
- Thread plug and ring gauges for metric, UNC/UNF, BSP and NPT threads, made to ISO 1502 and related standards.
- Taper plug and ring gauges for Morse, metric and custom tapers.
- Special and custom gauges such as depth, width, flush-pin and receiver gauges, made to your component drawing.
All of these are explained, with sizes and options, in our plain gauges guide.
GO gauge vs NOGO gauge: the differences
- Size: GO is made to the maximum material limit, NOGO to the least material limit.
- Length and form: GO is longer and full-form; NOGO is shorter or truncated.
- Wear: GO wears faster because it enters every good part, so it carries a wear allowance. NOGO should rarely enter a part.
- Marking: NOGO ends are usually identified by a red band or marking, and both ends are engraved with size, tolerance class and GO or NOGO.
Materials and accuracy
Standard plain and thread gauges are made in OHNS (oil-hardening non-shrinking) tool steel, equivalent to AISI O1, hardened to about 60–62 HRC. Sub-zero treatment and seasoning keep the size stable over years. For very high volumes or abrasive materials, tungsten carbide or chrome-plated gauging surfaces last much longer.
Gauge tolerances and wear allowances are specified in standards such as ISO 1938-1 and IS 3455 for plain limit gauges, and ISO 1502 for metric thread gauges. A good manufacturer works to these and states it on the certificate.
How to use a GO/NOGO gauge correctly
- Clean the gauge and the part. Chips, coolant and burrs cause false rejections.
- Let the part and gauge reach the same temperature. A warm part straight from the machine measures larger than it is.
- Use the gauge under its own weight, without force. If you have to push a GO plug in, the bore is undersize.
- Check the full length of the feature with GO, and several positions with NOGO.
- Store gauges in their case, lightly oiled, and never use them as a hammer or lever.
How often should GO/NOGO gauges be calibrated?
A GO/NOGO gauge slowly wears with every check, so it has to be calibrated to prove it still represents your drawing limits. Typical intervals are:
- 3 to 6 months for gauges used continuously on high-volume lines.
- 6 to 12 months for normal shop-floor use.
- 12 months for setting masters and gauges used occasionally.
Your quality system (IATF 16949, ISO 9001, AS9100) expects calibration by an ISO/IEC 17025 accredited lab, with traceability to national standards. SVNM's NABL-accredited lab (certificate CC-2472) calibrates plain, thread, snap and taper gauges, and you can read more in our guide on how often to calibrate gauges.
Why buy GO/NOGO gauges from SVNM
SV Nanometrology is a manufacturer and exporter of GO/NOGO gauges with its own NABL-accredited calibration lab under the same roof. Every gauge is made in OHNS steel, lapped to size and calibrated in-house before dispatch, so you receive the gauge and its accredited certificate together. We make standard sizes and gauges to your drawing, and supply customers across India and worldwide.
Frequently asked questions
What is a GO/NOGO gauge?
A GO/NOGO gauge is a fixed limit gauge with two members made to the two limits of a tolerance. The GO member must fit the feature and the NOGO member must not. If both conditions are met, the part is within tolerance.
How does a GO/NOGO gauge work?
For a hole, the GO plug is made to the lower limit and must enter, while the NOGO plug is made to the upper limit and must not enter. For a shaft, the GO ring or snap gauge is made to the upper limit and must pass over the shaft, while the NOGO is made to the lower limit and must not.
What are the types of GO/NOGO gauges?
The main types are plain plug gauges, plain ring gauges, snap or gap gauges, thread plug and ring gauges, taper gauges, and special gauges such as depth, width and flush-pin gauges made to a component drawing.
What is the difference between a GO gauge and a NOGO gauge?
The GO gauge is made to the maximum material limit, is full-length and checks the whole feature. The NOGO gauge is made to the least material limit, is shorter and checks one dimension at a time. NOGO ends are usually marked in red.
Which material is used for GO/NOGO gauges?
Most GO/NOGO gauges are made in OHNS tool steel (AISI O1) hardened to about 60–62 HRC and stabilised by sub-zero treatment. Tungsten carbide or chrome-plated gauges are used where wear is very high.
How often should GO/NOGO gauges be calibrated?
Usually every 6 to 12 months, and every 3 to 6 months for gauges in continuous high-volume use. Calibration should be done by an ISO/IEC 17025 (NABL) accredited laboratory.
Ask us about GO/NOGO gauges
Send your drawing or specification and we will reply with a quotation, usually within one working day. Every gauge is supplied with a calibration certificate from our NABL-accredited lab (ISO/IEC 17025, CC-2472).
- Manufacturer and exporter, supplying customers worldwide
- Made to your drawing, standard or sample
- Calibrated in-house before dispatch